1. <tbody id="7luvp"><nobr id="7luvp"></nobr></tbody>
      <menuitem id="7luvp"></menuitem>
    2. <progress id="7luvp"></progress>
      <progress id="7luvp"><bdo id="7luvp"></bdo></progress>
        <samp id="7luvp"></samp>
      1. <progress id="7luvp"></progress>

          1. How to control pressure during injection molding

            How to control pressure during injection molding

            Summary:Whether it is a hydraulic or electric injection molding machine, all movement during the injection p...

            Whether it is a hydraulic or electric injection molding machine, all movement during the injection process creates pressure. Appropriate control of the required pressure can produce a finished product of reasonable quality. Pressure regulation and metering system On hydraulic injection molding machines, all movements are performed by the oil circuit responsible for the following operations:

            1. Screw rotation in the plasticizing stage.

            2. Sliding seat channel (note nozzle close to the nozzle bushing).

            3. The axial movement of the shot screw during injection and holding pressure.

            4. Close the substrate to the plunger until the toggle is fully extended or the piston clamping stroke is complete.

            5. Start the top of the assembly ejector to eject the components.

            On a full voltage machine, all motion is performed by a brushless synchronous motor with permanent magnets. The rotary motion is converted to linear motion by the ball bearing screw that has been used in the machine tool industry. The efficiency of the entire process depends in part on the plasticization process, where the screw plays a key role.

            The screw must ensure that the material is melted and homogenized. This process can be adjusted with back pressure to avoid overheating. The mixing element does not produce excessive flow rates which would otherwise cause degradation of the polymer. Each polymer has a different maximum flow rate, and if it exceeds this limit, the molecules will stretch and the polymer backbone breaks. However, the focus remains on controlling the forward axial movement of the screw during injection and holding.

            Subsequent cooling processes, including intrinsic stress, tolerances, and warpage, are important to ensure product quality. This is all determined by the quality of the mold, especially when optimizing the cooling channels and ensuring effective closed-loop temperature regulation. The system is completely independent and does not interfere with mechanical adjustments. Mold movements such as closed mold and ejection must be accurate and efficient. A velocity profile is usually used to ensure that the moving parts are in close proximity.

            Contact maintenance can be adjusted. Therefore, it can be concluded that the product quality is mainly determined by the system that controls the forward movement phase of the screw without considering the energy consumption and mechanical reliability, and the same additional conditions (such as mold quality). On hydraulic injection molding machines, this adjustment is achieved by detecting oil pressure. Specifically, the oil pressure activates a set of valves through the control plate, and the fluid acts through the manipulator and is regulated and released.

            Injection speed control includes options such as open loop control, semi-closed loop control, and closed loop control. The open loop system relies on a shared proportional valve. The proportional tension is applied to the desired proportion of fluid so that the fluid creates pressure in the injection barrel, allowing the injection screw to move at a certain forward speed. The semi-closed loop system uses a closed loop proportional valve. The loop is closed at the position where the closed port is located, and the closed port controls the flow ratio of the oil by movement within the valve. The closed loop system closes at the screw translation speed.

            A speed sensor (usually a potentiometer type) is used in the closed loop system to periodically detect the drop in tension. The oil flowing out of the proportional valve can be adjusted to compensate for the speed deviation that occurs. Closed loop control relies on dedicated electronics integrated into the machine. Closed-loop pressure control ensures uniform pressure during the injection and hold-up phases and ensures uniform back pressure in each cycle.

            The proportional valve is adjusted by the detected pressure value, and the deviation compensation is performed according to the set pressure value. In general, hydraulic pressure can be monitored, but detecting melt pressure in the nozzle or cavity is another effective method. A more reliable solution is to manage the proportional valve by reading the nozzle or cavity pressure readings. Increasing temperature detection based on pressure detection is particularly beneficial for process management.

            Knowing the actual pressure the material can withstand also helps predict the actual weight and size of the molded part based on set pressure and temperature conditions. In fact, by changing the holding pressure value, more material can be introduced into the cavity to reduce component shrinkage, in line with design tolerances (including preset injection shrinkage). Semi-crystalline polymers show great specific volume changes near melting conditions. In this regard, overfilling does not prevent the component from ejecting.

          2. 23 Jun

            What factors should be considered when choosing an injection molding machine?

            When choosing an injection molding machine, several factors should be considered to ensure it meets the specif...

          3. 15 Jun

            What are the factors to consider when selecting an injection molding machine for your production needs?

            When selecting an injection molding machine for your production needs, several factors should be considered to...

          4. 07 Jun

            Efficiency and Performance Optimization of Strong Crushers Machines

            Efficiency and performance optimization are crucial aspects when it comes to Strong Crusher Manufacturers. Max...

          5. 黄色视频在线观看免费